Shadoweclipse13's New Project Thread!

[efiug]

Wild and chaotic sounds better to me, only downside i think would be trying to recreate certain sounds you'd find, wouldn't be as easy as just taking a picture probably.

[hexes]

rackmounting unbalanced devices and using a patch bay is a huuuuuge recipe for noise and signal loss. my advice is keep your usual order. i like to put gain stages and distortions in different places. absoLUTELY a distortion after a reverb, or a delay, but also some before.

[Shadoweclipse13]

rackmounting unbalanced devices and using a patch bay is a huuuuuge recipe for noise and signal loss. my advice is keep your usual order. i like to put gain stages and distortions in different places. absoLUTELY a distortion after a reverb, or a delay, but also some before.

Have you ever done something similar before? I love seeing how other people accomplish things like this!

I could always get a couple buffers if signal loss becomes a thing. As for noise, I'm planning to do things much like my board itself, and attempt to run power and audio cables either on opposite sides, perpendicular to each other (and not cross paths much), or both.

[Shadoweclipse13]

Just posted this in The Synth Thread, and decided to put it here to keep all my project stuff together too.

Since the wedding has passed, and we finally got the house back together and cleaned after getting back from our European honeymoon, I finally some time to work on this! I had some edge-glued wood from a board game shelf that I built a few years ago (which I decided to go a different way with, and disassembled), so that's what I used for this project. I cut enough wood for 2 cabinets (one for the pedals, and one for the other rack modules) down to 14" wide. I finally bought some short (6U) rack rails for the upper cabinet (the one for the other rack modules), so, then I can finish putting the second rack together. But for now, until those come and I finish building the other cabinet, I just put all my modules into this one...





Now I just need a ton of patch cables to go from the back of the patchbays (still need 2 more) to the pedals themselves. I ordered some pedalboard tape from The Gig Rig this morning, and have a couple new pedals on the way as well, so I will have to mess around with pedal order. Having to mess with efficient order and layout on the sliding server rack shelves, making patch cables, and hooking up power supplies, sounds like a really fun winter project

[sal paradise]

The only problem is when you need to get something out of the freezer…

[Shadoweclipse13]

The only problem is when you need to get something out of the freezer…

That's just for right now. My whole area in the basement is stupidly unorganized. I made a small bench for sitting and putting your shoes on years ago (very similar to my homemade amp stand), but I never used it for that, so my bass amp is on it right now. I'm gonna move some things around, and put the pedal and rack cabinets on that until I can make a dedicated stand for my cabinets. To be honest, the cabinets are mostly just a proof-of-concept right now, as I don't know what space I'll have to work with next year if we buy a house. I may just make built-in racks or something. If nothing else, if I like where everything is and how it all works, I'll want to patch some holes in the wood I used for the cabinet, and stain/clearcoat it to protect the cabinet. So, we shall see what the next few months bring

[sal paradise]

The only problem is when you need to get something out of the freezer…

That's just for right now. My whole area in the basement is stupidly unorganized. I made a small bench for sitting and putting your shoes on years ago (very similar to my homemade amp stand), but I never used it for that, so my bass amp is on it right now. I'm gonna move some things around, and put the pedal and rack cabinets on that until I can make a dedicated stand for my cabinets. To be honest, the cabinets are mostly just a proof-of-concept right now, as I don't know what space I'll have to work with next year if we buy a house. I may just make built-in racks or something. If nothing else, if I like where everything is and how it all works, I'll want to patch some holes in the wood I used for the cabinet, and stain/clearcoat it to protect the cabinet. So, we shall see what the next few months bring

Seriously though, they look amazing. Great job

[Shadoweclipse13]

The only problem is when you need to get something out of the freezer…

That's just for right now. My whole area in the basement is stupidly unorganized. I made a small bench for sitting and putting your shoes on years ago (very similar to my homemade amp stand), but I never used it for that, so my bass amp is on it right now. I'm gonna move some things around, and put the pedal and rack cabinets on that until I can make a dedicated stand for my cabinets. To be honest, the cabinets are mostly just a proof-of-concept right now, as I don't know what space I'll have to work with next year if we buy a house. I may just make built-in racks or something. If nothing else, if I like where everything is and how it all works, I'll want to patch some holes in the wood I used for the cabinet, and stain/clearcoat it to protect the cabinet. So, we shall see what the next few months bring

Seriously though, they look amazing. Great job

Thanks Sal! I wish I'd thought of it earlier. All thanks to Zork for giving me the idea. It's hard to commit to any one specific pedal order, when things can be so good in a different order here and there, so the patchbay idea is SO perfect for me. I'm seriously super excited to get going on this.

[Shadoweclipse13]

It's been a while since I've had an update! In my little free time lately, I've been trying to go through stuff in my area in the basement to purge or organize, getting ready for a possible move in the next few months. My current temporary workbench is now clear enough that I have enough room to finally get back to assembling/reassembling a few guitar projects! In the meantime, I've got a few little things going on.

[PATCHBAY PEDALBOARD]
Since the last pictures, I've removed all the 19" modules except for the shelves and the patchbays that the pedals will go to. So here's that:



The whole guitar/music area currently:


With a few things not pictured, this could basically be my submission for the "show your entire pedal collection" thread. Still need some velcro for the pedals too. Envelopes, octaves, compressors on the right, phasers and tremolos on the left:


Gain on the right, delay and reverb on the left:


The left is empty (supplies and cables for the project), but the right has my weird stuff (Electro-Faustus noise machines, bass DI, and Digitech SDrum):


[CONSOLE STEEL/SLIDE GUITAR]
I finally got off my ass and started drawing up my ideas for the slide guitar design. I've had a shape in my head for a while, and this is what I've come up with in Illustrator so far. There are 4 variations here, and I added these to a new poll above. They are the same overall shape, but the only difference here in these pictures is the shape of the carve on the outer "wings". This first picture, the inner edge of the carve is parallel to the fretboard:


#1 (Picture 1 Top) - Parallel carve, straight lines to the edge
#2 (Picture 1 Middle) - Parallel carve, angled lines to the edge
#3 (Picture 1 Bottom) - Parallel carve, curved lines to the edge

Second picture, the inner edge is angled in relation to the fretboard, closer to the fretboard by the headstock/tuners, farther from the fretboard by the bridge/pickups:


#4 (Picture 2 Top) - Angled carve, straight lines to the edge
#5 (Picture 2 Middle) - Angled carve, angled lines to the edge
#6 (Picture 2 Bottom) - Angled carve, curved lines to the edge

The 4 corners will have a slight rounded edge (I couldn't get Illustrator to properly round all 4 corners, so I just left it as is, and will do that later without it drawn on the template). As for the fretboard area carve, I like what I've got here, but none of the angles are 100% yet. I also like the idea of the lines to the edge being curved, but haven't drawn that up yet. But yeah, I'm open to any ideas that any of you fine folks who've got an eye for details may have. So I left a poll spot #7 for any other ideas

[Shadoweclipse13]

Its been a long while since I've made any progress on anything music- or guitar-related, and I apologize to anyone who was interested and then heard nothing! I posted when I got bodies back from painting by our own, fabulous, Copacetic! Still haven't done anything with any of those 2 bodies, but that's about to change! Reassembling my Tele Custom and my Jag Bass is about to happen as I've finally ordered a new pickguard for my Tele and new plates for the Jag Bass I ordered from Herad, will be shipping shortly!

Basically, if you can't tell, I'm fairly indecisive, in that, the possibilities are numerous, specifically with pot values and switching options. So, what I decided a while back is that I'm going to be installing a volume/tone bypass switch (what Sid Nitzerglobin calls the blower switch) on most or all of my guitars going forward.

For the Tele, I wired it like a traditional 70s Tele Custom, with a volume and tone pot for each pickup, and I'd like to replace it with a master volume and tone, but I'm not sure how I'll like the sound for both pickups, so this way, I can try a few out before committing to a set of pot values (or going back to the double volume and tones).

For the Jag Bass it's similar, but since the MM humbucker gets split, I've got a few weird ideas to play with (including a switch that would use one set of volume and tone values for full humbucker, and another for split, if it makes a difference).

Even if I don't change any values, I like having the bypass switch on both, so that'll be nice in any case. The new plate on the Jag Bass is the upper Jag plate, which now has a spot for TWO DPDT sliders (one for phase of the neck side of the humbucker, and one for the bypass switch) and two DP3T sliders for each half of the humbucker. I'll be dumping the 3-way toggle for the humbucker half selection, and opting for a rotary, so there will be no more dead spots. I'll post the schematics as I finish them in case anyone is interested.

[Shadoweclipse13]

[Console Slide Guitar]

Finally printed the design I worked up in Illustrator. This thing is huge! I kinda wonder if I want to slim down the angle of the perimeter, so I don't have to glue on a little extra wood on the edges to make the wood chunk I've got wide enough.


From the butt looking up.


From the head looking down.



Close-ups of the hardware (custom Herad plate for the bridge, Tele bridge pickup and KT-100 for the neck position (both from Roadhouse before he stopped making pickups!), 7-string width fretboard blank, and template for headstock.

[Shadoweclipse13]

It's been a while since I've posted anything. Since the move, I've only really been able to work on the house, and haven't had much time for fun projects, not even as much on my shop itself. I took some pictures of my shop as it is this morning just so you guys can see the wonderful space I've got to work with, but also how much of a mess it still is









I'm going to be building (starting today hopefully, and will probably take a few weeks) 4-6 workbenches. One will be electronics/soldering and guitar specific, one for my 3D printers and filament, and a general workbench or two. At some point, I'll figure out my desk/office situation (for some computer work and/or gaming, hopefully with a 2-monitor setup). I need to remove the 2 floor cabinets, and the 1 hanging/upper cabinet, once I build some general shelving for my paints and solvents, and places for some of the tools currently on top of the countertops. The drawers in the workbenches will have dedicated spaces for my tools using a combination of foam and 3D-printed inserts (Gridfinity) for tools and other things.

I bought plans for the workbenches from the guy who makes this channel, as I loved his design. The thing I love most about this design is a minimal amount of wood used, and drawers that don't use any expensive metal drawer glides. Which also makes it easy to populate drawers with tools, as you don't have to commit to what tools go in which space, since you can just move the drawers around.
Hooked On Wood - Save HUNDREDS of dollars building your workbench like this!

I'll also be removing the pegboard behind the back wall, and will be installing some French cleats behind the workbenches too. I'm thinking about some French cleat holders for my shop books as well, according to workbench use (electronics and guitar books above the electronics/guitar workbench, etc.).

To help make the workbenches accurately, I built this portable miter saw station yesterday, so I can easily cut wood at repeatable and accurate lengths. I will be cutting a groove into the MDF top for some T-track, so I can add a stop block and make repeatable cuts up to 8'/96".

[sal paradise]

Love the new space. Building your own cabinets is such a cool project- have you decided on the final layout? Looking forward to how this & future builds shape up

[BTL]

That drawer system looks great, and I'm envious of your new workspace. Very nice!

[Shadoweclipse13]

Love the new space. Building your own cabinets is such a cool project- have you decided on the final layout? Looking forward to how this & future builds shape up

Thanks Matt! I haven't decided a final layout yet for where the workbenches and cabinets will go in the shop, but I've got a few variations of the workbenches themselves that I'm planning.

The workbench that Dennis shows in that video has 2 columns of drawers, and an empty space on the left for a router. I'm not mounting a router to it, so I modded it to be 3 columns of drawers fitting across the whole thing. For my electronics/guitar workbench, I plan to leave the gap between the top of the drawers and the workbench top, so I can safely store and protect a guitar project that I'm in the middle of, but when I'm not working on it at the moment.

For my 3D-printing workbench, I did away with the gap, so it's 3 columns of drawers all the way from the bottom to just below the workbench top.

I'm thinking that I'm gonna make a really weird one or two for the garage, with drawers near the top (closer to the workbench top), with a gap underneath, for lumber storage.

I'm considering remaking my big assembly table, with a custom variation of the workbenches here as a base (2 or 3 workbenches, maybe a little shorter in height than this design is), so I could move it out of the space if I ever needed a ton of floor space for a specific project.

As for placement, the only one I know is the 3D-printer workbench. That one will got to the left of the drain pipe (white PVC) underneath the window (seen in picture #3 above), since the previous owner put in a huge exhaust fan, mounted between the floor joists. That way, I can tap off of the exhaust fan and print some serious filaments like ABS (that need venting for air quality-sake).

That drawer system looks great, and I'm envious of your new workspace. Very nice!

Thanks Brad! It's a really lovely space, and I never thought that I'd have something like this, without a big barn out in the country. I'm sacrificing my own parking space in our two-car garage, so I can set up the saws (miter, table) and router. I don't want to make any sawdust inside the house, especially since the house was made in 1964. If it was a new house that we were building, I'd pay to seal everything a bit tighter, and then just get good dust collection, but I don't think I would be able to seal anything up well enough for that here.

One thing that I'm considering is to run a length of 3/4"/1" black pipe from the garage to the shop, so I could have access to compressed air in the shop (staple or nail guns, and a small air gun to blow things off), but where the air compressor can still be in the garage (space and noise).

I mentioned that the shop will be my "office" as well, and to that end, I'm putting some fun (non-tool/non-useful) stuff in there too. I recently 3D printed some Facehuggers from the Alien films, to hide all over the shop, like my shop is infested I found a cool tutorial to make an egg that I may hide in the ceiling, and I might print some chestbursters I found as well


These fuckers are huge!!!