Struggling to raise the pickups on my Jazzmaster

For help with setups and other technical issues.
Post Reply
User avatar
jason1297
PAT PEND
PAT PEND
Posts: 2
Joined: Tue Mar 21, 2023 5:46 am

Struggling to raise the pickups on my Jazzmaster

Post by jason1297 » Tue Mar 21, 2023 8:19 am

I've had my Vintera Jazzmaster for about 3 months now, and have decided to have a go at adjusting the pickups. When doing this, I'm assuming that turning the screws clockwise will lower the pickups and counter clockwise will raise them. When I turn the screws counter clockwise, they just start coming out of the pickup rather than raising that side of the pickup.

The image below is of the bridge pickup, as I'm pretty sure this is not at maximum height.

Image

Am I missing something obvious here, or would it be better to take it to a guitar tech if I am not experienced in working with electrics?

User avatar
efiug
PAT. # 2.972.923
PAT. # 2.972.923
Posts: 162
Joined: Fri Sep 24, 2021 4:33 pm

Re: Struggling to raise the pickups on my Jazzmaster

Post by efiug » Tue Mar 21, 2023 8:33 am

Jazzmaster pickups are normally held up with a bit of foam placed underneath so its likely that the foam on yours is compressed and won't expand.

User avatar
Larry Mal
PAT. # 2.972.923
PAT. # 2.972.923
Posts: 19673
Joined: Mon Nov 29, 2010 4:25 pm
Location: Saint Louis, MO

Re: Struggling to raise the pickups on my Jazzmaster

Post by Larry Mal » Tue Mar 21, 2023 9:30 am

It's weather stripping foam, so you can get it at any hardware store, just pull the played out stuff that you have in there and get some thicker kind. It's a very common thing to have to do.
Back in those days, everyone knew that if you were talking about Destiny's Child, you were talking about Beyonce, LaTavia, LeToya, and Larry.

User avatar
jason1297
PAT PEND
PAT PEND
Posts: 2
Joined: Tue Mar 21, 2023 5:46 am

Re: Struggling to raise the pickups on my Jazzmaster

Post by jason1297 » Tue Mar 21, 2023 9:42 am

Larry Mal wrote:
Tue Mar 21, 2023 9:30 am
It's weather stripping foam, so you can get it at any hardware store, just pull the played out stuff that you have in there and get some thicker kind. It's a very common thing to have to do.
Sounds nice and easy. What thickness would I be looking at? Had a check online and my local store does 10mm or 20mm.

User avatar
Larry Mal
PAT. # 2.972.923
PAT. # 2.972.923
Posts: 19673
Joined: Mon Nov 29, 2010 4:25 pm
Location: Saint Louis, MO

Re: Struggling to raise the pickups on my Jazzmaster

Post by Larry Mal » Tue Mar 21, 2023 10:04 am

jason1297 wrote:
Tue Mar 21, 2023 9:42 am
Larry Mal wrote:
Tue Mar 21, 2023 9:30 am
It's weather stripping foam, so you can get it at any hardware store, just pull the played out stuff that you have in there and get some thicker kind. It's a very common thing to have to do.
Sounds nice and easy. What thickness would I be looking at? Had a check online and my local store does 10mm or 20mm.
A little hard for me to say exactly, but I see that 20mm is a little more than three quarters of an inch, and looking at my tape measure I think that would be what I would buy.
Back in those days, everyone knew that if you were talking about Destiny's Child, you were talking about Beyonce, LaTavia, LeToya, and Larry.

User avatar
Embenny
PAT. # 2.972.923
PAT. # 2.972.923
Posts: 10363
Joined: Tue May 24, 2016 5:07 am

Re: Struggling to raise the pickups on my Jazzmaster

Post by Embenny » Tue Mar 21, 2023 10:32 am

It also shouldn't really matter what thickness it you buy. Whatever thickness I have on hand, I often end up either cutting in half, doubling up, layering a half thickness piece on top of an intact one, etc.

It comes down to trial and error with whatever combination of rout depth, pickup thickness, and neck angle a particular guitar has, plus however squishy that particular piece of foam turns out to be.

You basically want to find the correct amount of foam that compresses enough that you can still lower the pickup, while resisting enough that it pushes the pickup upward as soon as you loosen the screws. There's no specific quantity or density of foam you can say will do that for certain. You just want medium-ish density foam in a reasonable shape and quantity, and the rest is trial and error.
The artist formerly known as mbene085.

User avatar
andy_tchp
PAT. # 2.972.923
PAT. # 2.972.923
Posts: 8010
Joined: Fri Apr 02, 2010 1:36 am
Location: Brisbane

Re: Struggling to raise the pickups on my Jazzmaster

Post by andy_tchp » Thu Mar 23, 2023 10:34 pm

The stock stuff is around 5mm. Just buy a length of the 10mm thick stuff and cut it into pieces to suit.
"I don't know why we asked him to join the band 'cause the rest of us don't like country music all that much; we just like Graham Lee."
David McComb, 1987.

Post Reply